Skip to content
site-logo

LACI JANE

AFFORDABLE MAXIMALIST ECLECTIC HOME DECOR | EASY DIYS

  • Home
  • PRESS
  • Blog
    • DIY’S
    • RENTAL HACKS
    • FURNITURE MAKEOVERS
    • ROOM MAKEOVERS
    • Lifestyle
  • DISCOUNT CODES
  • SHOP
  • Home
  • PRESS
  • Blog
    • DIY’S
    • RENTAL HACKS
    • FURNITURE MAKEOVERS
    • ROOM MAKEOVERS
    • Lifestyle
  • DISCOUNT CODES
  • SHOP
DIY'S

DIY EPOXY RESIN GUITAR PICK TABLE TOP: HOW TO EPOXY TABLE

DIY EPOXY RESIN GUITAR PICK TABLE TOP: HOW TO EPOXY TABLE

*This project was featured on Shutterfly and Bob Vila

This project has been….a BIG one. I love to do projects and share them with you, and you get to learn from my mistakes! And if you make a mistake, it’s OK cuz you will learn from them.

I started off by sanding down and painted the table. This was unfinished wood to begin with, so this process wasn’t necessary, but I wanted a really clean and smooth surface to paint on.

You’re gonna need guitar picks…& A LOT of them. Like, at least 200 guitar picks than you THINK you need. Just in case.

Measure the square footage of your surface. (Multiply length x’s width in inches since a guitar pick is about an inch)

This table was 36″ x 20″ = 720 total inches

and it took a little less than 1,000 guitar picks.

I bought my guitar picks in BULK from Amazon

MATERIALS:

  Guitar picks (I used these)

 Mod Podge or Wood Glue (I used wood glue the first time, but I was hauling this table around to the workshop and back. I needed something very strong just in case it got bumped. I didn’t want to lose any guitar picks)

NATURAL Paintbrush (for oil based paints/stains)

  Epoxy

Brad Nailer

Wood Glue

Wood Filler

DIRECTIONS:

I started by gluing my guitar picks to the table. I used mod podge to glue the guitar picks onto the table.

UPDATE!! I REALLY wish I would have known that I could’ve made my OWN guitar picks. Not only is it SO MUCH CHEAPER, but I would’ve been able to personalize it even more. This guitar pick maker makes it so easy to make your own guitar picks. 

Make sure you know how you want the picks lined and how they will fit onto your surface before you start gluing it down. You could even draw up a graph, just make sure you won’t be able to see it once the picks are down. I put each row the same way. One row facing upwards, and the next row facing down.

The mod podge goes on white and dries clear. Once you cover the top of the picks with the glue, you won’t be able to see what colors you put down until it dries, so make sure you lay out your picks before you glue them down.

Glueing the picks down took me a total of about 6-8 hours total. I woke up early to work on it before I went to work & after I got Jayli to bed I worked on it until my eyes couldn’t take any more.

BUILD YOUR FRAME

To build the frame, we had to remove the guitar picks I had put on there. Oops!

The next thing to do was to build a border around the table.

UPDATE: I wish I could tell you what size wood we used for the border, but I don’t know. The gentleman that helped me build this table passed away shortly after we finished making this table. He was an excellent woodworker and created the most beautiful items. He would know what size these wood pieces were, but I can’t ask him. The good news is that your table will more than likely be a different depth and need your own size! Just make sure that it’s thick enough to cover your guitar picks and epoxy.

We sanded the sides and applied wood glue to all four sides.

 If your border isn’t tall enough, your objects are going to stick out of the epoxy. Build your edge the same height or higher than your materials. This is important because you have to cover your entire surface and objects with epoxy.

Gluing the wood side pieces on takes two people to make sure it’s flush. One person holds the level piece of wood  *we will call this the sample piece* on the side while the other person puts the actual piece of wood on the side of the table, while pushing it up against the sample piece of wood.

It’s better to cut your wood a little longer than you need and sand it off. (Rather than it being too short, obviously)

Here’s a close up of the border. The epoxy will be flush with this.

After gluing the wood down-nail it.

Fill it in with some wood filler and sand it down.

I didn’t get many pictures after this because I was busy helping, but you can watch my YouTube video linked above.

It’s important to get all the dust, dirt and debris or else it will be stuck inside your liquid glass forever!  We used an air pressure hose on it and a tack cloth to ensure we weren’t getting any dust or hair trapped in the DIY guitar pick table.

Then, we made sure the table was completely level.

We followed the directions inside the box.

We used 2 boxes of epoxy because we needed the thickness of the epoxy thicker than 1/16 (the guitar picks are about 1/16 thickness and the epoxy needs to cover them.

After pouring the epoxy on the table, we used a squeegee to level it. And a natural brush (used for oil based paints/stains) for the sides of the table.

TIP!You don’t need a squeegee. Get a board (make sure it’s level) and it needs to be wider than the width of the table. You and a friend stand on opposite sides of the table. Each of you, together, run the board across the table. This would ensure it would be completely flush with the frame. 

After you have the epoxy completely spread out and level, you’re going to see bubbles and imperfections. But don’t freak out! THAT’S NORMAL.

Take a torch and apply heat about 4-6 inches from the table. You will see the bubbles disappear! It’s so cool!!

Then you let your table cure for however long the box says. I let mine cure for about 3 days.

Pictures don’t do it justice! It’s so hard to get a good picture of the glossiness, because it’s clear. Check out my Youtube video to see the whole process and how it looks, too!

The hardest and most time consuming process is just getting everything set up, cleaned off, and leveled. The epoxy is pretty much the fastest and easiest part 🙂

To see how I made this into a fold down table, click here.

TIP!! I REALLY wish I would have known that I could’ve made my OWN guitar picks. Not only is it SO MUCH CHEAPER, but I would’ve been able to personalize it even more. This guitar pick maker makes it so easy to make your own guitar picks. 

SHOP THIS PROJECT

 

Related

SHARE THIS
DIY EPOXY RESIN TABLEdiy guitar pick tableepoxy tableguitar pick tablehow toHOW TO RESINideasresin table
About Laci

About Laci

Hey, I'm Laci and I'm so glad you're here! I love sharing eclectic, vintage, MAXIMALIST, FUN home decor, easy DIY'S, and offer an award winning virtual interior design service✌🏻 I LOVE creating content and sharing my work with you!

Related Posts

DIY FAUX FIREPLACE
DIY FAUX FIREPLACE
DIY RULER GROWTH CHART
DIY RULER GROWTH CHART
DIY FILING CABINET MAKEOVER
DIY FILING CABINET MAKEOVER
DIY WALL CANDLE SCONCES
DIY WALL CANDLE SCONCES

Post navigation

Crystiles Peel and Stick Backsplash (FAQ + INSTALLATION GUIDE)
DIY WALL CANDLE SCONCES

3 comments

  1. Pingback: it's a wrap: JANUARY - LJDECOR
  2. Pingback: DIY Fold-Down Kitchen Table (Space Saver) - LJDECOR
  3. Pingback: DIY FOLD-DOWN TABLE (SPACE SAVER) - LACI JANE

Leave a ReplyCancel reply

Hey there!

Hey there!

Laci, Founder
I'm Laci and I love sharing affordable home decor and easy DIYS. Make sure to subscribe to my newsletter for weekly favs!

Popular Posts

DIY PEEL N STICK STAINLESS STEEL!?!
DIY'S ➤ June 17, 2017

DIY PEEL N STICK STAINLESS STEEL!?!

Hey guys! Today I’m going to show you how I transformed my appliances  with DIY peel and stick faux stainless steel contact paper. I put this faux stainless steel on my  refrigerator, stove, and dishwasher....

Read More
DIY FAUX STACK OF BOOKS- MODEM ROUTER HIDER
DIY'S ➤ March 11, 2019

DIY FAUX STACK OF BOOKS- MODEM ROUTER HIDER

I’m going to show you how to make a DIY electronic hider. This faux stack of books is great for hiding routers, cords, plugs, outlets, money, secret documents, jewelry, or to conceal other items.  What...

Read More
DIY GLITTER TABLE (THE EASY WAY)
DIY'S ➤ June 20, 2018

DIY GLITTER TABLE (THE EASY WAY)

Hey guys! Today we’re going back to the basics. I’ve made DIY glitter tables in the past using epoxy, but today we’re trying a new method using polyurethane, loose glitter, and paint. This method worked...

Read More
DIY RAG CURTAINS | Upcycle Your Fabric Scraps: DIY Easy Rag Curtains
DIY'S ➤ April 10, 2018

DIY RAG CURTAINS | Upcycle Your Fabric Scraps: DIY Easy Rag Curtains

DIY Rag Curtains using scrap fabric is a great way to upcycle fabric scraps in this STUNNING, affordable, and easy DIY! Who loves a (practically) FREE DIY!? 🙋‍♀️ If you have some scrap fabric laying...

Read More
  • Home
  • PRESS
  • Blog
    • DIY’S
    • RENTAL HACKS
    • FURNITURE MAKEOVERS
    • ROOM MAKEOVERS
    • Lifestyle
  • DISCOUNT CODES
  • SHOP
Copyright © 2025 | All Rights Reserved |
Loading…

 

Loading Comments...